ASTM D1693乙烯塑料的环境应力破裂的标准试验方法—标准名称

ASTM D1693 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics

ASTM D1693乙烯塑料的环境应力破裂的标准试验方法

ASTM D1693乙烯塑料的环境应力破裂的标准试验方法—适用范围

Scope：

This test method may be used for routine inspection purposes by subjecting a required number of specimens to the test conditions for a specified time and noting the number that fail. The cracking obtained with the test reagent is indicative of what may be expected from a wide variety of surface-active agents, soaps, and organic substances that are not absorbed appreciably by the polymer.

ASTM D1693乙烯塑料的环境应力破裂的标准试验方法—引用文件

ASTM D618 Practice for Conditioning Plastics for Testing

ASTM D883 Terminology Relating to Plastics

ASTM D1204 Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature

ASTM D1248 Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable

ASTM D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials

ASTM D4703 Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets

ASTM D4976 Specification for Polyethylene Plastics Molding and Extrusion Materials

ASTM E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

ASTM D1693乙烯塑料的环境应力破裂的标准试验方法—相关标准

ASTM D1693乙烯塑料的环境应力破裂的标准试验方法/Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics

GB/T 1842塑料 聚乙烯环境应力开裂试验方法/Plastics-Tset method for environmental stress-cracking of polyethylene

GB/T 2951.41电缆和光缆绝缘和护套材料通用试验方法第41部分： 聚乙烯和聚丙烯混合料专用试验方法耐环境应力开裂试验——熔体指数测量方法——直接燃烧法测量聚乙烯中碳黑和（或）矿物质填料含量一热重分析法(TGA)测量碳黑含量一显微镜法评估聚乙烯中碳黑分散度/Common test methods for insulating and sheathing materials of electric and optical cables-Part 41: Methods specific to polyethylene and polypropylene compounds-Resistance to environmental stress cracking-Measurement of the melt flow index-Carbon black and/or mineral filler content measurement in polyethylene by direct combustion-Measurement of carbon black content by thermo gravimetric analysis(TGA)-Assessment of carbon black dispersion in polyethylene using a microscope

ISO 8442-1与食品接触的材料和制品 刀具和凹形餐具 第1部分:准备食物用刀具的要求/Materials and articles in contact with foodstuffs - Cutlery and table holloware - Part 1: Requirements for cutlery for the preparation of food

GB/T 15819灌溉用聚乙烯（PE)管材由插入式管件引起环境应力开裂敏感性的试验方法和技术要求/Polyethylene(PE)pipes for irrigation laterals-Test method and specification of susceptibility to environmental stress cracking induced by insert-type fittings

BS 5577非金属手柄餐桌用刀叉餐具规范/Specification for table cutlery with non-metallic handles