阻燃防火材料-网上贸易平台 | | WAP浏览
服务热线:4006555305
当前位置: 首页 » 防火测试中心 » 各国标准法规 » 美国 » 正文

ASTM D1676带绝缘薄膜的磁性导线的标准试验方法

放大字体  缩小字体 发布日期:2012-02-08   浏览次数:164  分享到: 分享到腾讯微博
ASTM D1676带绝缘薄膜的磁性导线的标准试验方法
ASTM D1676 Standard Test Methods for Film-Insulated Magnet Wire
ASTM D1676带绝缘薄膜的磁性导线的标准试验方法
Bond strength values obtained by flexural tests can provide information with regard to the bond strength of a particular self-bonding outer coating in combination with a particular round film-insulated magnet wire when measured under conditions described in this test method.
1. Scope
1.1 These test methods cover procedures for testing film-insulated magnet wire that is used in electrical apparatus. These test methods are intended primarily for the evaluation of the electrical insulating materials used. The intent is that these test methods be used, except where modified, by individual specifications for particular applications.
1.2 These test methods present different procedures for evaluating given properties of round, rectangular or square, copper or aluminum film-insulated magnet wire.
1.3 The values stated in inch-pound units are the standard. The SI units in parentheses are provided for information only.
1.4 The test methods appear in the following sections:
 
Sections
Bond Strength
4-12
Burnout (AC Overload Resistance)
13-21
Chemical Resistance
22-28
Coefficient of Friction
29-37
Continuity, DC High Voltage
38-45
Continuity, DC Low Voltage
46-53
Completeness of Cure
54-60
Cut-Through Temperature (Thermoplastic Flow)
61-68
Dielectric Breakdown AC Voltage
69-75
Dielectric Breakdown    AC   Voltage after Bending
76-82
Dielectric Breakdown AC Voltage at Elevated Temperatures
83-89
Dielectric Breakdown AC Voltage after Conditioning in Refrigerant Atmosphere
90-99
Dimensional Measurement
100-106
Dissipation Factor Measurement
107-114
Electrical Resistance
115-121
Elongation
122-129
Extractables, Refrigerant
130-140
Film Adherence and Flexibility
141-148
Formability:
 
a) Elastic Ratio
152
b) Low Stress Elongation
153
c) Spring Back
154-155
Heat Shock
156-162
Oiliness
163-169
Scrape Resistance, Unidirectional
170-177
Solderability
178-185
Resistance to Insulating Liquids and Hydrolytic Stability
186-195
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazard statements are given in 9.5, 19.1, 19.3, 19.8, 52.1, 58, 59.1, 74.1, 112.1, 135.4, and 182.3.
Note 1—This test method is related to IEC 60851. Since both methods contain multiple test procedures, many procedures are technically equivalent while others differ significantly.
 
2. Referenced Documents (purchase separately)
ASTM Standards
A228/A228M Specification for Steel Wire, Music Spring Quality
B3 Specification for Soft or Annealed Copper Wire
B43 Specification for Seamless Red Brass Pipe, Standard Sizes
B193 Test Method for Resistivity of Electrical Conductor Materials
B279 Test Method for Stiffness of Bare Soft Square and Rectangular Copper and Aluminum Wire for Magnet Wire Fabrication
B324 Specification for Aluminum Rectangular and Square Wire for Electrical Purposes
B609/B609M Specification for Aluminum 1350 Round Wire, Annealed and Intermediate Tempers, for Electrical Purposes
D149 Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies
D150 Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation
D374 Test Methods for Thickness of Solid Electrical Insulation
D877 Test Method for Dielectric Breakdown Voltage of Insulating Liquids Using Disk Electrodes
D1533 Test Methods for Water in Insulating Liquids by Coulometric Karl Fischer Titration
D1711 Terminology Relating to Electrical Insulation
D2475 Specification for Felt
D2519 Test Method for Bond Strength of Electrical Insulating Varnishes by the Helical Coil Test
D5423 Specification for Forced-Convection Laboratory Ovens for Evaluation of Electrical Insulation
E4 Practices for Force Verification of Testing Machines
E6 Terminology Relating to Methods of Mechanical Testing
E8 Test Methods of Tension Testing of Metallic Materials
E220 Test Method for Calibration of Thermocouples by Comparison Techniques
E1356 Test Method for Assignment of the Glass Transition Temperatures by Differential Scanning Calorimetry or Differential Thermal Analysis
E1545 Test Method for Assignment of the Glass Transition Temperature by Thermomechanical Analysis
Other Documents
IEC60851 Methods of Test for Winding Wire
Index Terms
bond strength; burnout; chemical resistance; coefficient of friction; continuity; completeness of cure; cut-through temperature; dielectric; dimensional measurement; dissipation factor; elastic ratio; electrical resistance; elongation; extractables; film adherence; film-insulated conductor; formability; heat shock; hydrolytic stability; low stress elongation; magnet wire; oiliness; overhead resistance; scrape resistance; solder-ability; spirngback; thermoplastic flow; resistance to insulating liquids;
 

  详情请咨询
  防火资源网-阻燃防火测试中心
  电话:(+86)0592-5056213
  传真:(+86)0592-5105807
  邮件:firetest@firetc.com

凡注明"防火资源网"的所有作品,由<防火资源网>整理编辑,任何组织未经<防火资源网>及其拥有者授权,不得复制、转载、摘编或利用其它方式应用于任何商业行为。

 
 
[ 防火测试中心搜索 ]  [ ]  [ 告诉好友 ]  [ 打印本文 ]  [ 关闭窗口 ]  [ 返回顶部 ]

 

 
 
推荐防火测试
推荐图文
点击排行
 
 
网站首页 | 广告服务 | 关于我们 | 联系方式 | 服务协议 | 版权声明 | 网站地图 | 友情链接 | 网站留言 | 旧版本 | 闽ICP备09009213号
©2019-2021 FIRETC.COM All Rights Reserved   备案号:闽ICP备09009213号-1在线客服 点击QQ交谈/留言 点击QQ交谈/留言